Sunday, October 21, 2012

Stripped sprockets and alien parts.

Hey everyone, been a while since I posted, but I have been quite busy. First off, pulled the engine to take a closer look and replace gaskets, and we have some issues. First off the front drive sprocket.
It's completely rounded out, which makes some sense. When I got the bike running a few weeks ago I tried to drive it in first gear, and it would only barely crawl. I was scared the whole transmission was blown, but now I'm surprised the bike moved at all. New sprocket is around $90. What makes it worse, is the previous owner drove on it and not only destroyed the sprocket but also chewed up the shaft it connects to. 
Output Shafe
So I went on eBay and got a whole used transmission, shifting linkage, and everything for only $30 shipped. Next we moved on to disassembling the rest of the engine so we could replace the gaskets and make sure everything else is in good working order. The gaskets needed some real TLC, due to the fact that their wasn't any. They used liquid gasket sealer and it got everywhere but where it should be.

After removing the clutch, we split the case and found something. (picture below)
We then spent the next hour or so figuring out where it went, looking at diagrams and examining all the parts, but we could not figure out where it went. We guessed that the old owner replaced something in the block that was broken and missed this little guy. Then, after figuring out how a manual transmission actually works (which I did figure out) I found where our mysterious piece came from.





This is where the shift lever connects to the transmission to shift into different gears. If you jam really hard down on the shifter, this is the piece you break I suppose. Here is another picture of it removed, it was broken is a few places and is one solid casting, luckily the transmission I bought comes with one.









That is about as far as we got this weekend, now just waiting for some parts and tools to come in so we can finish assembly. Below are some other pictures I took during the build.
Bottom view of the engine with the case split.
Left side of the motor with clutch removed.

Trying to keep the computer / repair manual clean.

Thank for reading, check back next week, should make good progress by then. 

Tuesday, October 9, 2012

Day One

Hey everyone, and welcome to My KZ440D Mod Shop blog! 

Last week I decided I wanted to find myself a new winter break project so I browsed Craigslist and found a perfect match, so I bought it. It's nothing special, just a Kawasaki KZ 440D. I'm pretty satisfied with what I got. The engine runs, suspension looks good, carbs cleaned, tires look great, new battery, no major rust on the frame and it comes with a bunch of extras. Including: a stock tank, a yamaha tank (for doing a cafe conversion), two yamaha seats (one is pretty bad, other is good), a brand new seat cover, all in one rear light/turnsignals, a set of front and rear LED turn signals, new petcock, service manual, 12 inch shorty exhaust pipes, and complete engine gasket kit. Not too bad for only $700, here's a few pics of the bike I got. (plenty more to come)



So far I have done a few things. First off, I removed the make-shift rear light holder. It was literally a bent piece of steel bolted on to the frame with two 10 led segment lights attached to it, with the most shady wiring. So now I have two extra lights I can use on the bike. Along with that, I started tackling the other wiring issues.

About the shady wiring, of the previous owners thought it would be a good idea to wire up part of the rear lights, but they didn't have a long enough piece of wire, so they attached on a 6 inch piece of green wire, to a black wire, no biggie. Then it was still too short, so they attached a red wire to the green wire, but that wire was still too short, then they attached another black segment. With that being said I am going to go through the entire electrical system and mend these errors.

After I got most of the rear wiring labeled and removed unnecessary wire, I started onto the tank. I was given two keys with the bike, one for the actual bike ignition, and another unknown key. Well the unknown key doesn't fit either tank or the helmet lock. Luckily the tanks were open already so I started on the original tanks lock. Took it apart and cleaned it, now it works perfectly, with any key too! Not that I want it to be open to anyone, but it's something that's not on the top of my to-do list. As for the rest of the tank, there was some light surface rust inside the tank, I could scrap some of it off with just my finger. For the time being, I tapped off the petcock opening and put some paint thinner inside to prevent any more rusting.

This weekend I am planning on putting the tank on, getting her fired up and going for a little test drive. If that checks out, I'm going to pull the heads and replace the gasket that is leaking. If I still have some time left over, I'll start tearing into the front end wiring.